Commissioning a Staircase Pressurization System is the final, critical step in transforming a building from a "Construction Site" into a "Safe Occupancy." In 2026, BOMBA (Malaysian Fire Department) and UBBL (Uniform Building By-Laws) standards require precise atmospheric balancing. If the pressure is too low, smoke enters the stairs; if it is too high, the fire doors become impossible to open, trapping occupants inside.
As part of a Ventilation Systems Audit, EKG provides the rigorous Testing & Commissioning (T&C) required to prove your "Safety Envelope" is 100% compliant.
To be commissioned as "Fit for Purpose," the staircase system must achieve three distinct aerodynamic targets:
The Pressure Shield (+50 Pa): With all doors closed, the staircase must maintain a positive pressure of 50 Pascals (pm 10%). This physically prevents smoke from "leaking" into the escape route.
The Force Limit (110N): We use a digital force gauge to ensure that even under full pressurization, the force required to pull open a fire door does not exceed 110 Newtons.
Airflow Velocity (1.0 m/s): When a door is opened, the fan must instantly compensate. We measure the "Blast" across the open doorway to ensure a minimum velocity of 1.0 meter per second, which acts as an air curtain against encroaching smoke.
We go beyond simple "Fan Starts" to audit the entire volumetric performance of the building:
Multi-Floor Mapping: We measure the pressure on the ground, middle, and top floors simultaneously. This identifies the Stack Effect (hot air rising), which can cause the top of a KL tower to be over-pressurized while the bottom is unprotected.
VFD "Fire Mode" Parameter Lock: We audit the Variable Frequency Drive (VFD). We ensure it is programmed to "Run-to-Destruction," ignoring standard motor trips (like overheating) to prioritize human life over equipment protection.
Ductwork Integrity Audit: If the fan is at 100% speed but the stairs only hit 30 Pa, we use thermal imaging and ultrasonic leak detectors to find "Air-Thievery" in the shafts or duct joints.
Interlock Timing: We measure the seconds between the Fire Alarm signal and the fan reaching its "Steady State." Compliance requires a reliable response in under 60 seconds.
A "Commissioned" system is also an efficient one. Many systems are left "un-tuned," running fans at maximum speed and wasting massive amounts of energy during mandatory monthly tests.
Friction Elimination: We identify "Parasitic Drag" from misaligned pulleys or tight bearings that force the motor to work harder.
The Logic: Because of the Cube Law, if we optimize the mechanical path so the fan can hit its 50 Pa target at 42Hz instead of 50Hz, the power consumption during testing drops by nearly 40%.
| Test Parameter | Target Performance | Safety Risk of Failure |
| Static Pressure | 50 Pa (+/- 10%) | Smoke Ingress (Low) / Stuck Doors (High) |
| Door Opening Force | Max 110 Newtons | Evacuation Blockage (Safety Hazard) |
| Air Velocity | Min 1.0 m/s (Door Open) | Smoke Backflow into Stairwell |
| Genset Changeover | < 10 Seconds | Total System Failure during Blackout |
| Motor Vibration | < 2.8 mm/s | Bearing Seizure during Emergency |
BOMBA Form G Support: We provide the comprehensive technical reports and "Witness Logs" required for your annual Fire Certificate (FC) renewal.
Mechanical Restoration Path: If you fail commissioning, we don't just walk away. We are experts in Mechanical Fan Overhauls, offering on-site dynamic balancing, bearing replacements, and motor repairs to get you to compliance.
VFD ROI Projection: We calculate the exact energy savings achieved by "Down-Speeding" your fan to its precision safety setpoint.
2026 Technical Standards: We use the latest digital manometers and thermal cameras to ensure your building meets the latest UBBL and MS (Malaysian Standards) codes.
Malaysia
